Received 191 Likes on 153 Posts. 2003 Ranger Trouble Codes (check engine light) My friend has a 2003 Ranger Edge with 4.0 V6. The truck runs great, but the check engine light is on, so it won't pass inspection. I read the codes and got these two, P0171 and P0174. They indicate that both banks are lean. Does anyone know what might be causing this?Definition of Diagnostic Trouble Code P2008 This Definition of P2008 is Applied to All Manufacturers Powertrain: Intake Manifold Runner Control Circuit/Open Bank 1 I also was told that it was the battery because they charged it and cleared the fault codes and nothink came back up when the car was started back up. 2009 Dodge Journey OBD Codes p2004, p2017 and p2008 2009 Doge Journey SE, 2.4L V4 with 87000 miles Code 1 p2004 "Intake Manifold Runner Control Stuck Open Bank 1" - I replaced the intake manifold runner control valve. It was relatively easy. 3 bolts and 1 connector. General C-Max Discussions. Fault Codes & Fault Diagnosis. P2008 OBD 2008 Inlet control valve on Inlet Manifold. Jump to Latest Follow
These are the main fault codes you’ll find when reading out the ECU: P0403 – Exhaust Gas Recirculation Circuit Malfunction. P0607 – Control Module Performance. P1585 – Throttle Control Unit Malfunction. P2008 – Intake Runner Control Circuit Open Bank 1. P2110 – Throttle Actuator Control System.
J.C Avis Low Range 4WD Posts: 113 Joined: Thu Feb 03, 2011 1:47 pm Town: Otjiwarongo Vehicle: 2002 Toyota Hilux D/c 4x4 3.0 KZ-D-4D. Suspencion lift,160 liter spare tank. Navigator spots. Double battery system. Tour 'trallies'. Spare wheel carrier. Roof rack. Canopy. Real Name: Japie Location: Namibië How to Diagnose the P2009 Code. A P2009 is a generic trouble code that can be logged in vehicles with an OBD-II system. However, keep in mind that the steps for diagnosis and repair can vary, depending on vehicle specifications. If you’re not familiar with the process of diagnosing trouble codes, it’s best to leave the job to the pros. Above approximately 3000 rpm, the vacuum solenoid will be de-energized. This will allow a vacuum to vent from the actuator and the butterfly valve plates to open. The Diagnostic Trouble Code (DTC) indicates a failure in the IMRC primary control circuit. P2008 2006 Ford Fusion Code - Intake Manifold Runner Control Circuit/Open Bank 1. A P0013 trouble code is also a generic code that translates to an exhaust camshaft position actuator actuator solenoid control circuit issue. The camshaft actuator system is also referred to as variable valve timing (VVT) The system allows the computer to change the intake and exhaust camshaft timing to vary how and when the valves open and close.Hi all, I have been experiencing loud exhaust noise and juddering. This typically occurs in stop-start driving scenarios but has occurred from immediate motorway driving. The following Fault Code has appeared: P244C: 00-6D – Exhaust Temperature Too Low for Particulate Filter Regeneration, Bank 1
Ok so another update, after a week the light came back on, i have since found that the solenoid runner control valve is the issue but the problem i have is that it seems i have a weird engine type that was bang in the middle of the crossover from focus c max to c max. i have a 57 plate and it has the 1.8 duratec engine in it. the solenoid control valve that is in it is showing on all the What is the Cost to Diagnose the Code P1336 Ford? Labor: 1.0. The cost to diagnose the P1336 Ford code is 1.0 hour of labor. The diagnosis time and labor rates at auto repair shops vary depending on the location, make and model of the vehicle, and even the engine type. Most auto repair shops charge between $75 and $150 per hour. The trouble code P2008 can be elucidated as Intake Manifold Runner Control Circuit/Open Bank 1. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and KPS9UP.